Jump to content
Sign in to follow this  
MST Engineer

1994 Miata 1.8 Race Ready with spares $6,100

Recommended Posts

Selling my Champcar and WRL GP3 Miata to fund the build of a new yet undecided car for next season.  Car started life as a Chumpcar hence the lack of parts like rear bumper but under the fun look is a well refined Champcar/WRL car.  Car is a 94 1.8 Miata with the following modifications 

 

XIDA Race Coilover Suspension (1 event)

Bilstein yellow sport shocks w Flyin Miata Springs (Off car but can be swapped easily)

Thickened stock front swaybar
Supermiata rear sway bar
Energy Suspension control arm bushing kit (1 event)
All new upper and lower control arms every corner (1 event)
All four wheel bearings (1 event)
Supermiata extended lower balljoint (1 event)
NB sport front brake caliper/rotors with DTC70 Pads
New rear brake calipers DTC30 pads
Head coolant reroute
Aluminum radiator 
Kirkey containment seat
NB torsen lsd with KIA sportage 4.7FD
Tall person cage and 1.5" floor drop fits drivers 6'3" with ease
Extensive chassis light weighting (2080lbs race weight)

 

Car is ready to race with exception on normal reprep, oil/filter etc.  Asking price is $7200 OBO for the car as is on one of 3 sets of wheels and used tires.  Willing to negotiate price delivered to areas in the Midwest.  Also comes with full set of spare arms, spare rotors/calipers/pads and spare trans.

 

Spares List

Set of front and rear rotors

Set of front pads (DTC60)

Set of rear pads (DTC30)

Set of front calipers (non sport size)

Set of rear calipers (need rebuild)

Pair front upper control arms

Pair front lower control arms

Pair rear lower control arms

Pair rear upper control arms

Pair of front hubs

Spark plug wire set

Spark plugs

Bilstein Yellows with FM spring cut one link

5spd transmission (unknown condition from junkyard)

Rear differential cover/carrier with broken ear (good core for welded

Passenger side 2 part axle (good used)

Driver side 2 part axle (broken outer boot needs rebuild)

Garage fabed fuel catch pan fits around rear tire

 

Price is $7100 OBO with all spare or $6100 OBO without Xidas Coilovers and on Bilstein Yellows

 

rHgiwgi.jpg

lLhnRki.jpg

ftXnUa4.jpg

[Imgur](https://i.imgur.com/6fUdE5t.jpg)

oWCk9f2.jpg

RsRWprQ.jpg

NV5UFsi.jpg

NSmSpOu.jpg

jRx5Ek9.jpg

D4Yh1mA.jpg

Cxf8TfL.jpg

sOKcaYj.jpg

etCAs4O.jpg

PyJCWUM.jpg

 

Edited by MST Engineer

Share this post


Link to post
Share on other sites

Hi, a couple questions/requests for pictures

 
What is a "thickened stock sway bar"? Can you post a picture of it?
 
What's going on with the gorilla tape radiator ducting? 
 
Since I can see some surface rust can you take some shots of underneath the rocker panels? Are there any other problematic rust spots?
 
I can't quite tell from the pictures but it looks like there's no passenger seat, and no way to add one. Am I correct? Also more pictures of the passenger compartment would be helpful.

Oh, and doest it comes with the hood prop? :)
 
Thank you!
Edited by iig

Share this post


Link to post
Share on other sites
On 10/12/2018 at 11:27 AM, iig said:

Hi, a couple questions/requests for pictures

 
What is a "thickened stock sway bar"? Can you post a picture of it?
 
What's going on with the gorilla tape radiator ducting? 
 
Since I can see some surface rust can you take some shots of underneath the rocker panels? Are there any other problematic rust spots?
 
I can't quite tell from the pictures but it looks like there's no passenger seat, and no way to add one. Am I correct? Also more pictures of the passenger compartment would be helpful.

Oh, and doest it comes with the hood prop? :)
 
Thank you!

 

The center part of the stock swaybar was sleeved with a piece of pipe to increase stiffness at the cost of metal instead of points for aftermarket bar.  I will try and get a picture but its under the front plastic cover.

 

Radiator was closed out with all aluminum tape to keep water temps down but some of that came loose at a wet race so was replaced with gorilla tape.  Might look silly but significantly improves water temps for summer races.

 

Car just has some light surface rust from sitting under a cover outside for a bit at my new house while i was making room for it.  No structural rust but I will try and get some pictures of the underside this weekend.

 

Car has no passenger seat but one could be added if battery box was moved to trunk or under the hood.  Seat would have to be closes to dash than driver side do to cage shape but has a normal door bar on that side.

 

Can come with prop tube shown or the well worn 2x1 stick that we normally take to races. ;)

 

Let me know if you have other questions.

 

 

Added more details about spare package.  Also car comes wired for Racecapture Pro 2 datalogger and can include unit for extra price.

Share this post


Link to post
Share on other sites

Added more pictures of the interior.  Currently has RaceCapture Pro 2 and ShiftX2 RGB Sequential Shift Light that can be included for additional $350.  Originally $650.  Will get some of the underside tomorrow.

Share this post


Link to post
Share on other sites

Sorry no interest in your car but sent you a PM .

 

Looks like a good car for a team to jump in a drive!

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now
Sign in to follow this  

×